PX and Zenco Flow, Like PB&J (jelly you don’t have one yet?)
PX and Zenco Flow, the next PB &J? Probably. Over the years we have used any number of devices to plug in our custom, 510 threaded carts – everything from simple “penjamins” to monster rig setups with computer games on the side; however, the Zenco Flow is the best 510 cart smoking experience we have had in our thirteen years since we started PX.
Our history with Zenco dates back to using the original version in our demo days, as an easy (and sanitary) way for folks to test out our cartridges. It is a glass cup and we could use alcohol swabs in between samples – what a great way to consume, like sipping a cocktail. For us though, it never reached “must have” status, personally, because the smoke was still the same temperature as the pen, and the device isn’t necessarily portable.
Enter the Zenco Flow, a new design with a water bubbler. Now your favorite PX cartridge takes an automatic draw and can then be pulled through ice water. The end result is like sipping a cool glass of water. Welcome to the oasis friends.
For us, nothing can take away the portability and convenience of the penjamin, but after several pulls the smoke can begin to get hot. Our custom battery does allow for temperature control, but even then, there’s just not a lot of room for smoke/heat/battery to exist. This is why the Zenco Flow is such a great alternative – it offers the cool vapor option we have so often sought. It might not be as portable as a pen, but for the home-couch smoke, the Zenco Flow + PX cart is a tough duo to beat.
And today we are excited to partner with Zenco, offering the Flow on our website. We have the Zenco Flow wood grain base and for a limited time only, a $30 discount on our “starter kit collection” which is our four most popular carts, our custom battery and the Zenco Flow. Please use code “pb&j” when checking out to redeem the coupon, and yes, this can be used with our running, bulk purchase option of four carts for $99 + free shipping (US only).
For more details on the Zenco Flow checkout below. When ready to buy, take a browse through our new strains and new artwork – our Wedding Cake and Trainwreck are dope – and as you know, we are always on the hunt for that new, new indoor so stay tuned for some new Preserve cured resin bangers coming your way soon!
How to charge the Zenco?
Before beginning your cloud sharing experience, give your Zenco a full charge. Although it may be able to power up right out of the box, it is highly recommended to fully charge your new Zenco before first use.
As part of the provided accessories, you will find a USB to USB-C cable. Plug that into the back of the Zenco base where the battery charge socket is, you should hear/feel a click, and connect it to your standard USB charger. Switch it on and leave it charging for 2 hours, even after the light has turned green.
The Zenco LED Light Indicator Guide
The easy to use, single touch button of the Zenco is surrounded by a color-coded LED light ring to communicate two key things – battery level and temperature settings.
What do they mean?
Battery Level
When switching on, the light blinks according to the battery level remaining:
- Green : 70% - 100%
- Blue : 30% - 70%
- Red : below 30%
Temperature Settings
Three taps on the button changes the temperature/voltage settings which are: -
- Yellow 2.5V – Lowest temperature. Thin, very flavourful vapor (recommended for dry herbs)
- Blue 3.0V – Medium temperature. Slightly thicker, smooth vapor
- Green 3.5V – Medium-high temperature. Thick vapor, less harsh
- Red 4.0V – Highest temperature. Thick and heavy vapor
LED light changes color
How to perform a vaporizer burn off?
When using brand-new vaporizers straight out of the box, it's important to always do an empty vaporizer burn off. It is a simple step to take that benefits your health and your new Zenco. An empty burn cleans the oven and removes any leftover manufacturing residue or dust. Follow these easy steps: -
- Switch on your device by rapidly tapping the button on the base 5 times. The light blinks to indicate it is switched on.
- Lift the magnetic top off the base and screw on your chosen accessory (quartz or ceramic coil) to the heating chamber. Make sure that you do not fill the coil with any aromatherapy material yet. You should see the light flash once showing that you have made a connection. Hand tighten from there. Replace the magnetic top.
- Change the temperature settings by using 3 taps on the button. A short vibration and LED indicator light colour change lets you know what temperature setting you’re on. Cycle it to the highest temperature by repeating the 3 taps until the colour is red.
- Once it is red, tap twice to activate auto-fill function. Let the Zenco run until it auto-shuts off.
- Repeat twice. Let it cool for 5 minutes and you’re all set.
- Perform the burnoff on each coil before first-use.
While you’re waiting for the chamber to cool, we recommend that you wash the Zenco glass cups with water and dishwashing liquid. Or you can also pop it in the dishwasher as all Zenco glassware is dishwasher safe.
Treat the Zenco Duo and Zenco Flow glasses like your drinkware, you wouldn’t use a newly bought cup without first giving it a good clean right?
How to use the Zenco?
Once the cups are cleaned and dried, and the burnoffs completed, you can load up the Zenco with your desired aromatherapy material.
Take one of the coils and fill it with your botanicals. The ceramic coil is for use with wax or concentrates. If you’re using dry herbs the quartz coil is recommended, jump to the next section for a more detailed guide on how to use the Zenco with dry herbs.
-
The Zenco’s base has a magnetic top that lifts off and reveals a 510 threaded base. Remove the magnetic top and screw in one of the coils or a 510 cartridge if you’re using that instead Once the filled coil or cartridge is in place, replace the magnetic top, and gently press the glass down.
- If you’re using the Zenco Flow, fill the glass with about 3cm of water. The water would remain at the top part of the glass and filter the vapor when you inhale later.
- You are now ready to fill the glass with vapor. Rapidly tap the button 5 times to turn on.
- It is recommended to start on the lowest temperature (Yellow) and work your way up if needed. Use 3 taps to change the voltage.
Fill the Zenco Flow glass with water
- There are 2 filling modes: Manual and Autofill.
\ Manual Fill : Tap and hold power button to fill glass to a desired amount.\ Autofill : Tap twice. It will run until you stop auto fill. Tap once to stop auto fill.
- For starters, we recommend filling vapor up to about 1/3 of the glass cup. Once glass is filled to your desired amount, gently lift the glass while holding down the base.
With the Zenco Flow, glass is filled with water. You’ll have to take a stronger inhalation to pull the vapor through the water bubbler.
*Note: There is a hole in the side of the Zenco Flow glass, that is NOT a carb hole. It is designed to allow vapor to enter and air to exit. DO NOT plug it with your fingers when you inhale the vapor as it will cause reverse suction with the water above and leak down into the unit.
- You can use the same 5 tap sequence when you want to switch it off. In case you forget, fret not, the Zenco auto-offs after a while.
COOL TIPS : Elevate Your Zenco Experience!
Put your own spin on the Zenco glass chambers by adding fun stuff like ice, a lemon slice or fresh herbs like mint for an even more chilled and flavourful experience.
You can also stick a straw into your Zenco glass to sip on the vapor for a smoother hit. Use it in a shared setting with your friends for added fun and also to avoid leaving the odd lipstick mark on the cup.
How to use the Zenco with Dry Herbs?
Included in both the Zenco Duo and Zenco Flow box is a quartz coil and ceramic coil. Pocket Ovens Chief Baker recommends using the quartz coil for dry aromatherapy herbs, and to start with the lowest heat setting.\ \ The coils do need replacements from time to time for optimum performance. If you find that it's not producing vapor anymore, now's the best time to pick up new coils!<!–\[if gte mso 9]>
</xml><!\[endif]–>
The screen like coil is the Ceramic Coil
You’re still going to get a bit of burning on those parts touching the coils. With the right steps you can limit it and get closer to vaporization, here’s how:-
- Grind up your aromatherapy dry herbs, Zenco recommends using a fine grind (almost like an espresso grind).
- Load your dry herb into the coil. Less is more, and only fill about half to three quarters of the way. Very lightly tamp it down, being careful not to overdo it, so we recommend using your pinky finger to be able to feel it out. Over packing it will increase the risk of burning your material.
- Screw the coil into the base of the Zenco vaporizer, hand tightening to make sure it is screwed all the way in so that it can heat up properly. Ensure that you do not over tighten it or it may get stuck.
- Replace the magnetic top, and gently press the Zenco glass down in place.
- Tap the button 5 times to switch on your Zenco. Then tap 3 times to cycle through the temperature settings and set the temperature to the lowest setting (Yellow).
- Touch and hold the button to manually fill the glass, and release the button once the vapor fills the glass 1/3 full. Visually you could check when to stop filling when it reaches the top of the black silicone diffuser in the glass.
*Note: Overfilling the glass is more likely to burn the herbs, and not only is that a major wastage, it would also make the coil harder to clean. We do not recommend using the autofill function for the same reasons. A controlled filling is key!
- Alternatively, you can use a timed method for filling. Touch and hold the button to manually fill for 2 seconds, stop and wait for 2 seconds, and repeat the steps until the vapor fills to your desired level. Short filling times and waiting in between heat-ups makes sure the oven does not get too hot.
- When ready, gently lift up the Zenco glass while holding down the base.
- Now is the moment you’ve been waiting for, inhale your cupful of milky white vapor!
*Note: If you’re using the Zenco Flow glass, the inhalation will be more of a rip than a sip. DO NOT plug the hole with your fingers when you inhale the vapor as it will cause reverse suction with the water above and leak down into the unit.
- Take off the magnetic cover to check the coil between hits to check for signs of your dry herb burning.
- You can use the same 5 tap sequence to switch off your Zenco aromatherapy vaporizer. In case you forget, fret not, the Zenco auto-offs after a while.
The more you use it the more you will learn to adjust the amount of herbs, temperature, and heat up durations. All herbs and blends have different characteristics like density and moisture, so try the heat settings starting with the lowest heat first, and work your way up. Zenco recommends using dry aromatherapy herbs that are more on the 62% humidity side. Find out what works best for you and the type of aromatherapy herbs you are using.
\